Zurn Z86300 Manuel d'utilisateur télécharger pdf

AQUASPEC FAUCETS

MODEL - Z86300 SERIES

SINGLE BASIN METERING

TECHNICAL INFORMATION

FLOW: 0.25 GPC MAXIMUM; PRESET AT FACTORY TO 10 SECOND @ 80 PSI ADJUSTABLE

MAXIMUM PRESSURE: 125 PSI

MAXIMUM TEMPERATURE: 180

- CAN USE QUARTER TURN CERAMIC DISK CARTRIDGE

INSTALLATION INSTRUCTIONS

1. THE WATER SUPPLY LINE MUST BE THOROUGHLY FLUSHED BEFORE FAUCET INSTALLATION.

2. REMOVE FAUCET BODY FROM CARTON AND PLACE GASKET (#7A) ON SHANK.

3. PLACE FAUCET ON SINK, MOUNT LOCKWASHER (#7B) AND MOUNTING NUT (#7C) ONTO SHANK FROM UNDER SINK.

4. HAND TIGHTEN MOUNTING NUT (#7C). MAKE SURE FAUCET IS CENTERED PROPERLY. DO NOT OVER TIGHTEN, YOU

COULD DAMAGE THE FIXTURE

5. ATTACH LAVATORY SUPPLY TO THE OUTLET OF THE STOP BODY AND CONNECT TO FAUCET WITH RISER NUT

(#7D).

6. OPTIONAL - POP-UP (-P)/ GRID STRAINER (-G)/HANDICAP OFFSET GRID DRAIN (-GH):

INSTALL POP-UP OR GRID STRAINER IN SINK OUTLET AND PLUMB WASTE CONNECTION.

7. TURN SUPPLY WATER ON AND OPERATE THE FAUCET WHILE CHECKING FOR LEAKS.

8. INSTALL AERATOR (#6) INTO FAUCET AND HAND TIGHTEN.

9. METERING CARTRIDGE IS FACTORY PRESET FOR A 10 SECOND CYCLE AT 80 PSI, IF ADJUSTMENT IS

NECESSARY, SEE “ADJUSTING THE FLOW” SECTION (PAGE 2).

PAGE 1 OF 4

IMPORTANTTHE WATER SUPPLY LINES MUST BE THOROUGHLY FLUSHED BEFORE INSTALLATION TO PREVENT

FOREIGN MATTER AND DEBRIS FROM CLOGGING AND/OR DAMAGING INTERNAL COMPONENTS AND THEREBY PREVENTING

THE FAUCET FROM FUNCTIONING PROPERLY

IMPORTANTTHE FAUCET HAS AN INTEGRAL SHANK FILTER ASSEMBLY INSTALLED IN THE BODY UNDER THE METERING

CARTRIDGE TO PREVENT FOREIGN MATTER AND DEBRIS FROM DAMAGING THE FAUCET. THE INTEGRAL FILTER MAY BE

REMOVED TO BE BACK-FLUSHED AND CLEANED IF INSUFFICIENT FLOW IS DETECTED. THE INTEGRAL SHANK FILTER

ASSEMBLY MUST BE RE-INSTALLED AFTER SERVICING TO ENSURE PROPER FUNCTIONING OF THE METERING CARTRIDGE.

Form # CF848 Date: 6/19/07

C.N. No. 105794 Rev. G

1 2 3 4

Résumé du contenu

Page 1 - AQUASPEC FAUCETS

AQUASPEC FAUCETSMODEL - Z86300 SERIESSINGLE BASIN METERINGTECHNICAL INFORMATIONFLOW: 0.25 GPC MAXIMUM; PRESET AT FACTORY TO 10 SECOND @ 80 PSI ADJUST

Page 2 - REPLACEMENT PARTS

ZURN INDUSTRIES, INC.COMMERCIAL BRASS OPERATIONS2640 SOUTH WORK STREETFALCONER, N.Y. 14733PHONE: 1-716-665-1132 FAX: 1-716-665-1135WORLD WIDE WEB

Page 3 - Z86300 PICTURED

PAGE 3 OF 4ITEM PART# DESCRIPTION QTY1 G60522 METERING HANDLE ASSEMBLY 11A 60601003 COLD METERING HANDLE 11B 62705001 SET SCREW 11C G60558 METERING IN

Page 4 - Problem Cause Solution

PAGE 4 OF 4Form # CF848 Date: 6/19/07C.N. No. 105794 Rev. GMetering Faucet Trouble Shooting GuideProblem Cause SolutionNo water dispensingfrom faucet.

Commentaires sur ces manuels

Pas de commentaire

Zurn Z86300 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Articles sanitaires Zurn Z86300. Zurn Z86300 User's Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Articles sanitaires Zurn Z86300